A409 Dirty Soccer Ball

$5.99

Shipping calculated at checkout

Available Now!

100% Satisfaction Guaranteed

Carmen

Approved

Printed Pattern Vinyl - 12"x12 sheet; 12"x4ft roll

Instructions for Printed Heat Transfer Vinyl Patterns (for use on shirts/fabrics)

Take your projects to a NEW level with our Printed Heat Transfer Vinyl (HTV) designs. Printed directly in our CCG Warehouse, our pattern HTV works best with our heat transfer mask (or carrier sheet) found HERE.

Items You'll Need

 Application Instructions
Applies To:

• 100% cotton
• Poly/cotton blends
• 100% polyester

Application Instructions:

• Print, cut, and weed material
• Mask with HTV Mask
• Apply design at 320°F/160°C with medium pressure for 15 seconds
• Peel COLD

Click HERE to watch our video

Detailed Instructions
    • STEP 1: Begin by placing your printed HTV pattern side up on your cutting mat (the backing of the vinyl is plain white and glossy).
    • STEP 2: Very important: DO NOT MIRROR your design. Before cutting, we recommend performing a test cut in a corner of your vinyl to check your settings. Start with the recommended settings and adjust pressure/force as needed to ensure you’re not cutting through the backing of the HTV (see table below for cutter settings).
    • STEP 3: Weed your design so that all excess vinyl is removed from the backing.
    • STEP 4: This is where you’ll need your HTV mask and a squeegee. Place your clear mask sticky side up on a flat surface. Take your weeded HTV design and place the pattern side down on the mask. (Try gently folding it like a taco and rolling it from the center out.) Apply firm pressure using a squeegee from the center of the design outward to remove air bubbles and to ensure the design adheres to the masking. Tip: Replace the mask's protective sheet and flip the design over. Squeegee once again, center outward to make sure all air bubbles are smoothed out.
    • STEP 5: Take the mask in one hand and the vinyl's backing in another. In one continuous motion, peel the backing and HTV mask apart. Tip: It is best to 'rip' the backing away in swift quick motions. The design should remain with the HTV mask.
    • STEP 6: Now the transfer is ready to be applied to the garment. Press the patterned HTV at 320° with medium pressure for 15 seconds. It is a cool/cold peel. Wait 10-20 seconds before peeling your mask, it should be cool to cold touch.
Cutter Settings

Cricut®:

Blade: Standard
Setting: Iron-on

Silhouette Cameo:

Blade: Standard, 3
Setting: Heat Transfer Material (smooth)
Speed: 8
Thickness: 6

Scan N Cut:

Blade: 2
Cut Speed: 1
Cut Pressure: 1

Roland GS/GX-24:

Blade: 45°
Gram Force: 80-90
Offset: .250
Speed: 25-50 cm/s

Graphtec: 

Blade: 45°
Gram Force: 8-9
Tool: CB09U+0
Speed: 30 cm/s



 _____________________________________________________________

Instructions for Printed Adhesive Patterns (for use on cups/decals)

Our custom made adhesive patterns are printed utilizing a professional printer on permanent gloss, permanent matte or indoor matte vinyl.  

This vinyl is top quality digital vinyl that is cut using any number of cutter/plotters. Compatible with Silhouette, Cricut, Graphtec, Roland, Brother and most any cutter you can find. To apply this vinyl you will need transfer tape which you can find HERE.

 Application Instructions

• Cut vinyl color side up; do not mirror design
• Weed excess vinyl
• Squeegee transfer tape over weeded design; push air from the middle outward
• Remove white backing (design will stick to transfer tape)
• Squeegee design onto clean surface, ensuring all bubbles are pushed out
• Remove transfer tape

Cutter Instructions

Cricut®:

Blade: Standard
Setting: Vinyl

Silhouette Cameo:

Blade: Standard, 2
Setting: Vinyl
Speed: 7
Thickness: 5

Scan N Cut:

Blade: 1
Cut Speed: 1
Cut Pressure: 2

Roland GS/GX-24:

Blade: 45°
Gram Force: 30-100
Offset: .250
Speed: 30 cm/s

Graphtec:

Blade: 45°
Gram Force: 16
Tool: CB09U+0
Speed: 25 cm/s